English
Inicio
Compañía
Productos
Instalaciones
Personal
Localización
Contacto
It's a grey/white mortar glue for high-medium absortion ceramics placing over the following surfaces:
* Cement
* Traditional brick walls
* Cement floors
* Monocomponent mortar-glue (only needs to add water)
* Nule vertical slip
* Thin layer application
* Excelent workability for walls and floors
* High frost resistance
1- Pour the water first and then, the mortar-glue.
2- Mix in bowls in an approximated proportion of 6 litres each 25 kgs.
3- It is very important to not add more water than recommended, because physical and chemical conditions would be then, reduced.
4- Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
5- Let it repose 5 minutes for the additives to act correctly and then mix again before use.
6- Never add more water after the paste has reposed.
* Substrate must be clean and dry.
* Extend the product with the smooth part of the trowel to ensure a complete contact with the substrate.
* Use the dented trowel (no. 6-8) in 1,5 - 2 m2 squares.
* Check that no surfacial film is formed over the adhesive. In such a case, it's enough to pass the trowel again with some fresh product.
* Place the ceramic leaving 2-3 mm joints.
* We recommend
- To leave 3 mm expansion joints in the extremes of the walls.
- For floors, leave 6 mm .perimeter joints
Ceramic materials placing, for walls and floors.
Using substrates: Cement, cement-lime mortar, brick and cement floors.
Substrates and surfaces must be solid, hard, clean and dry, without dust, grease or oxide.
Do not use: Over metal, concrete, fiber-cement, wood, tiles and old tiles.
In these cases, mix with ADESILATEX 1000 (6 litres each 25 kgs)
Aspect
Presentation
Thickness of the paste in walls
Thickness of the paste in floors
Output in walls
Output in floors
Mix water
Open time according to UNE EN 1346
Rectification time
Initial adherence according to UNE EN 1348
Adherence after water immersion according to UNE EN 1348
Adherence after frost cicle according to UNE 1348
Fire Reaction
Waiting time for rejointment in walls
Waiting time for rejointment in floors
Slip in vertical wall UNE EN 1308
Temperature during application
Paste density
Stockage
(from manufacturing date, under cover, in a dry place)
Grey/White Powder
25 kgs or 5 kgs bags
from 2 to 4 mm
from 5 to 7 mm
from 3,5 to 4 kgs/m2
from 6 to 9 kgs/m2
6-6,5 litres per each 25 kgs
20 minutes
10 minutes
1,3 N/mm2
0,9(grey)-0,7(white) N/mm2
1,1 N/mm2
A1
4-6 hours
24 hours
< 0,5 mm
min 5ºC, max 32ºC
1,6 gr/cm3
12 months
* Grey/White cement
* Siliceous soils
* Additives and resins
Product components are not contact toxic but are toxic to ingestion (in such as a case, go asap to an emergeny health service).
Keep away from children or animals.
Skin: Wash with plenty of water
Eyes: Wash with plenty of water
Ingestion: Rinse with water and drink plenty of water
It's on customer's responsibility the admission and control in the distributor's warehouse or construction, as well as the election of the product to be used on each case. Manufacturer's responsibility is limited to manufacturation defects and for the value of the merchandise because it's out of his control the material election and the work conditions.
Technical sheet for 2007.
